radial backlash

用法例句

The influence of radial clearance of sliding bearing on superheat failure of bearing Liang Baoying;

滑动轴承径向间隙对轴承过热故障的影响

The radial clearance of tLhe big joumal bearing in rock bit's bearing system is of great importance to the service behavior of the bit.

从润滑理论的分析表明，最小油膜厚度随半径间隙变化的幅度很小；从接触力学理论的分析表明，适当减小径向间隙值，可以降低轴承接触压力峰值；从摩擦发热角度的分析表明，减小配合间隙可以降低摩擦发热和磨损量；普通合金钢滑动轴承半径间隙值不小于0。

Taking the manufacture clearance into consideration under the special torque load and a constant speed,the right radial clearance of roller bearing is solved out through selecting among roller bearings with different radial clearances and making a summary of the analyzing results.

在一定转速和载荷作用下,通过选取不同的滚针轴承径向间隙,并考虑加工情况进行分析计算,对结果进行总结,找出适合的行星齿轮滚针轴承径向间隙,并在试验中进行了验证。

Rational selection of radial clearance of rolling bearing;

滚动轴承径向游隙的合理选择

Measurement and mating methods of radial clearance of spherical roller bearings;

调心滚子轴承径向游隙的测量和配套方法

Influence of inner ring double raceways centre distance of self-aligning roller bearing on radial clearance

调心滚子轴承内圈两滚道中心距对径向游隙的影响

Study on Normal Backlash of Involute Straight Bevel Gear Transmission based on Virtual Modification Principle

用虚拟变位原理研究锥齿轮传动的法向侧隙问题

Study on lateral boundary of roof water flowing fracture devel opment regularity

采空区顶板导水裂隙侧向边界发育规律研究

broadside seismic reflection profiling

侧向地震反射剖面法

broadside seismic refraction profiling

侧向地震折射剖面法

piston skirt clearance

(活塞侧缘和气缸之间的余隙) 活塞侧缘隙

Numerical Optimization Technique for Wheel Profile Considering the Normal Gap of the Wheel and Rail

基于轮轨法向间隙的车轮踏面优化方法

Test method for determination of radial interstitial oxygen variation in silicon

GB/T14144-1993硅晶体中间隙氧含量径向变化测量方法

Wavefield Simulation with the Pseudo-Spectral Method in Anisotropic Viscoelastic and Porous Media;

各向异性粘弹性孔隙介质伪谱法波场正演模拟

Fracture Parameter by DLL Interpretation and Its Application to Carbonate Rock

双侧向测井裂缝参数解释方法的应用

STUDY ON PUSHOVER ANALYSIS METHOD BASED ON LATERAL LOADING PATTERN

基于侧向力加载方式的Pushover分析方法

Abstract: The paper presents a method of improving machining accuracy in electrochemical machining by using a dual pole tool.

文摘:采用辅助阳极法来改善电解孔加工过程中侧面间隙电场的分布。

Two methods are usually used to increase gearing backlash for counter trains:1.Decrease addendum modification coefficient,but remain center distancein constant.

对于计数齿轮传动,通常采用两种方法增大侧隙:中心距不变,减小变位系数;

Preliminary Study on Treatment the Cervical spondylosis with Odontoid Lateral Mass Interval asymmetry by chiropractic

整脊手法治疗寰枢椎齿状突-侧块间隙不等导致颈痛的初步临床体会

impeller clearance

叶轮间隙;叶片间隙;导向叶片与工作叶片的间隙

sidepiercing cam actuated die

侧楔作用侧向冲孔模

Checking Connecting Rod Side Clearance—Typical

检查连杆侧间隙Clearance—典型的

Install rings and confirm ring side clearance:

安装活塞环，并确认活塞环侧间隙：

DECREASE SHIM THIS SIDE FOR LESS BACKLASH

对于较小的齿隙，减少这侧的垫片